Dear Michael,
We are currently using version 4.2.5.
We have 2 problems: 1. Some Current Main Calendar appointments are showing up on the new calendar we created yesterday. 2. Preview Error.
I went ahead and set up a couple of addresses under the new calendar "SS Statute Calendar" this morning. However, some of the current appointments in the Main Calendar are showing up in the new SS Calendar. I went ahead and entered a couple of dates (one for August - one for September) into the SS Calendar and tried to Print Preview the August-September information.
The Print Preview showed the two dates along with the appointment dates that were showing up on both calendars. I then tried to close out of the Print Preview and got the following message:
Error 12
Variable 'DATETIME' is not found.
"" + alltrim(STR(cal1.eventno))
CC_0_CALENDAR.GETMONTH
Line No 45
I tried printing this message - No luck. When I cancelled the box the "Do you want to quit A1 Law" message box appeared. I clicked on Cancel and it appeared 2 more times. I went to another system in the program but the quit message kept appearing.
Thoughts? Suggestions? Thanks!
Sincerely,
Michael Lerner
Lerner, Moore, Mammano, Strasser, and Silva
www.injuryatwork.com
(909) 889-1131
Extra Calendar Problem
-
Michael Appell
Re: Extra Calendar Problem
1. The Print Preview showed the two dates along with the appointment dates that were showing up on both calendars. I then tried to close out of the Print Preview and got the following message:
Make sure that the word CALENDAR (to the right of the calendar dropdown) is somewhat gray and not black. It acts like a ShowAll calendars for viewing and printouts. What you see in Custom is what you get on the print out.
The error you are getting sounds like a sort problem. Not sure what steps you did to create this error (you may have double clicked on a label somewhere). I would need a to know the steps to recreate it here.
2. I went to another system in the program but the quit message kept appearing
Try typing Ctrl-0 (that's control zero) to break out.
Mike
Make sure that the word CALENDAR (to the right of the calendar dropdown) is somewhat gray and not black. It acts like a ShowAll calendars for viewing and printouts. What you see in Custom is what you get on the print out.
The error you are getting sounds like a sort problem. Not sure what steps you did to create this error (you may have double clicked on a label somewhere). I would need a to know the steps to recreate it here.
2. I went to another system in the program but the quit message kept appearing
Try typing Ctrl-0 (that's control zero) to break out.
Mike
-
Michael Lerner
Re: Extra Calendar Problem
Dear Michael,
The Calendar was greyed out (Showall Not being used).
Steps taken:
1. Went to System - Calendar - General - To the Calendar Titles (2nd line) added "SS Statute Calendar".
2. Opened a Case Card - Calendar - Switched the Calendar to "SS Statute Calendar" - Clicked "Add a new appointment" - Changed the date to the statute date and added in the Event area "7/19/2002 due (statute date)". Posted the event and saved it to case activity.
3. Clicked on the "Month" tab - Changed the Calendar from "Main Calendar" to "SS Statute Calendar" (with the work "Calendar" next to it greyed out). Noticed that during the month some (about 14) that are on the "Main Calendar" are also showing up on the "SS Statute Calendar" (even though I've only added 2 new events to the "SS Statute Calendar")
Note: I checked an event that was showing up in both places and it was created back on 7/1 (while just created the "SS Statute Calendar" today). Is there a setting for events like a "have event show up in all calendars?"
Thoughts?
Sincerely,
Michael Lerner
Lerner, Moore, Mammano, Strasser, and Silva
www.injuryatwork.com
(909) 889-1131
The Calendar was greyed out (Showall Not being used).
Steps taken:
1. Went to System - Calendar - General - To the Calendar Titles (2nd line) added "SS Statute Calendar".
2. Opened a Case Card - Calendar - Switched the Calendar to "SS Statute Calendar" - Clicked "Add a new appointment" - Changed the date to the statute date and added in the Event area "7/19/2002 due (statute date)". Posted the event and saved it to case activity.
3. Clicked on the "Month" tab - Changed the Calendar from "Main Calendar" to "SS Statute Calendar" (with the work "Calendar" next to it greyed out). Noticed that during the month some (about 14) that are on the "Main Calendar" are also showing up on the "SS Statute Calendar" (even though I've only added 2 new events to the "SS Statute Calendar")
Note: I checked an event that was showing up in both places and it was created back on 7/1 (while just created the "SS Statute Calendar" today). Is there a setting for events like a "have event show up in all calendars?"
Thoughts?
Sincerely,
Michael Lerner
Lerner, Moore, Mammano, Strasser, and Silva
www.injuryatwork.com
(909) 889-1131
-
Michael Appell
Re: Extra Calendar Problem
I'm going to need to look at this remotely with you on the phone so that we may explore your unique situation. I can't seem to find any reason for this. We may then post the results on the forum so that other may learn what's happening. Please Email me so that we may set up about 15-30 minutes to look into this problem further.
Mike
Mike